The Edelbrock Pro-Flo 4 XT EFI Kit #35813 for 1986-earlier Small-Block Chevrolet engines is a complete bolt-on electronic fuel injection system featuring a black powder-coated XT intake manifold with large plenum and long tapered runners that comes ready to run with high-flow injectors, fuel rails and 90mm throttle body preassembled for you at the Edelbrock factory. This kit is rated at a maximum 625 horsepower with 35 lb/hr injectors and includes all supporting sensors, a wide-band O2 sensor, wire harnesses and Android-based tablet. Also included is a single-connection distributor designed to work specifically with Pro-Flo 4 providing fully sequential port injection and infinite control over ignition and fuel events under all conditions. Key Pro-Flo 4 advancements are its Self-Calibrating Fuel Map Technology, Wide-Band O2 Closed Loop Mixture Control, and new low-profile ECU with faster processor and upgraded Bluetooth chip for reliable connectivity with the E-Tuner app that comes preinstalled on the tablet. The E-Tuner includes a Setup Wizard to guide you through setup and provides fuel and spark adjustability for complete control over the system. Pro-Flo 4 EFI #35813 for the Small-Block Chevy requires no laptop tuning. Minimal setup and tuning adjustments are required with base calibrations provided in the software. The ECU is self-learning and will continually adjust the fuel injection calibration for maximum performance by maintaining a specified target air-fuel ratio as you drive. The E-Tuner provides the ability to fine-tune air-fuel ratios, ignition curve, idle speed, acceleration fuel, fans, rev-limiter and more. Multiple displays let you monitor engine performance in real-time from inside or outside of the vehicle while retaining the simplicity that Pro-Flo 4 systems are known for.
When choosing to upgrade your engine to modern fuel injection, look no further than Edelbrock's Pro-Flo 4 EFI systems. Edelbrock has been delivering the best combination of dyno proven electronic fuel injection performance for over 40 years. Pro-Flo 4 is not just a replacement for your carburetor, it's a complete engineered system that provides the ultimate in performance, drivability and quality. These easy to use, self-learning EFI systems feature an all new ECU pre-loaded with 80 dyno-tuned calibrations that support popular engine configurations up to 800 hp. Combined with the enhanced E-Tuner 4 App's easy to use setup wizard; you get plug and play performance without the need of a laptop or costly dyno tuning sessions. Pro-Flo 4 EFI systems are the most complete systems available on the market, giving you what you need to upgrade to powerful and efficient fuel injection for your vehicle. Pro-Flo 4 EFI systems are the best value for your dollar! ** INSTALLATION NOTE: These systems will require a high pressure EFI compatible fuel delivery system. Fuel delivery kits are available and sold separately. LS kits will require a coil harness which is sold separately. 24(x) reluctor applications will require #37-1633 and 58(x) reluctor applications will require #37-1632. #35760/#35770 manifold height: 4.58". #35780 Manifold height: 4.58". #35700/#35710 manifold height: 4.95". #35740/#35750 manifold height: 7.40". #35830/#35840 manifold height: 5.90". #35850/#35860 manifold height: 5.90". #359300 manifold height: 6.30". #335910 manifold height: 6.10". #35930/#35940 manifold height: 6.35". #35950 manifold height: 6.25". #35960 manifold height: 6.49". #35970/#35980 manifold height: 6.60". Throttle body height: 2.25"
Edelbrock; EFI; Pro-Flo 4; Pro-Flo 4 XT; EFI; Fuel Injection; Electronic Fuel Injection; Chevy; Chevrolet; Small-Block; SBC; Small-Block Chevy; SB Chevy; Mouse Motor; 350 Chevy; 327 Chevy; 283 Chevy; Edelbrock EFI; Edelbrock intake manifolds
Edelbrock, EFI, Pro-Flo 4, Pro-Flo 4 XT, EFI, Fuel Injection, Electronic Fuel Injection, Chevy, Chevrolet, Small-Block, SBC, Small-Block Chevy, SB Chevy, Mouse Motor, 350 Chevy, 327 Chevy, 283 Chevy, Edelbrock EFI, Edelbrock intake manifolds
Pro Flo 4 Fuel Injection Kit Xt Sequential Port Sbc 1986 & Earlier 625 Max Hp 35 Lbhr Injectors Black.
PRO FLO 4 FUEL INJECTION KIT XT SEQUENTIAL PORT SBC 1986/EARLIER 625 MAX HP 35 LbHr INJECTORS BLACK
Edelbrock Pro Flo 4 Fuel Inject Kit XT Seq Port SBC 429/460 1986 625 Max HP 35 LbHr Injectors Black
Edelbrock Triple Deuce Intake Manifold for 1938 to 1948 Ford/Mercury Flathead V8.
Pro-Flo 4 EFI XT-Style Kit #35813 For 1986 & Earlier Chevrolet Small-Block
Pro-Flo 4 EFI XT-Style Kit #35813 For 1986 Earlier Chevrolet Small-Block
Pro-Flo 4 XT EFI Kit for 1986 & Earlier Small-Block Chevy Engines, Black
Pro-Flo 4 XT EFI Kit for 1986 Earlier Small-Block Chevy Engines; Black
Pro-Flo 4 Fuel Injection Kit
Edelbrock Fuel Injection
Fuel Injector Kit
Fuel Injection
{ eo : 7in.}
ProFlo4 EFI
{"eo":"7"}
